![]() ![]() ![]() On a fresh boot up of Recalbox the roms loaded every time but when i exited a game with Hotkey + start about 50% of the time the game would go back to the MAME roms selection screen but i couldn't load another game successfully, if i rebooted and tried the next game it would work, i did this about 30 times to try the roms i wanted, same issue. So for MAME I have just used individual roms as I didn't want 2000+ games. So I think my first post was a bit all over the place as there was so many things that worked compared to Retropie but a few little things that didn't, but I was so close and frustrated with myself. If possible, flash Recalbox on a Pendrive and test on a computer, so you can test whether the problem is the system or the hardware (although it does not rule out a configuration problem or a problem with defective ROMs, for Thank you very much for taking the time to reply to me. There is no need to restart Recalbox to change the game, you did something wrong manipulation, or is overloading your Rpi1 somehow. You shouldn't have any problems with the SNES and Megadrive ROMs, the Rpi1 Hardware is enough.Īvoid using custom themes on Rpi1, and avoid using many types of consoles on Rpi1 (more than 20 for example - I don't know when it starts to overload), Rpi1 is very weak.ĭid you build your Recalbox yourself, or download a ready-made image from the internet? It is recommended that you set the Hotkey to Select. Rpi1 is weak hardware, you can't expect great performance, it can't even run all emulators:Ībout MAME: You need to check your ROMSET, it needs to be the same as the one requested by the core (The MAME 2000 core will only perform well with ROMSET MAME 2000 ROMs, you will probably be able to run many ROMS MAME 2003, but they may not have the desired performance).Ībout Rpi4: it is a novelty, but it runs most games very well, as far as I know (I don't have an RPi4) the only problems reported are in the N64 and some Dreamcast games. I can load and play the first game, but if i want to exit and change the game it only works 60% of the time and when it does it never starts the next rom? I don't think i am doing anything wrong as it repeated on 3 different emulators now with the same result. The hotkey is programmed as left 2 shoulder on the PS classic controller so L2 + start is supposed to boot back right? Which it does about 60% of the time. If i then reboot and load the rom that wouldn't load it works! So i basically have to reboot after every time i want to change a game?Īt first i thought it could be because it was MAME roms, but i have since tried SNES and Megadrive and its the same result? I have noticed that if i can boot back to the main menu it wont let me load another rom it just goes to a black screen and sits there (again even waiting 10mins) so i have to hard reset at this point. However it doesn't always boot back and I get the black screen, sometimes if i leave it for 10mins it goes back to the main menu other times it just sits there and i have to hard reset. I can now boot back to the main menu after changing the USB controller for a PS classic usb controller and reconfiguring the buttons. Ok so i am a little further forward after more testing and reading. I'm also guessing that the arcade stick/buttons are mapped in the exact same way as a controller is? Is there any recommendations for sticks i was going to start with a set of EG STARTS from Amazon and then if the project goes well maybe move to a Sanwa set later?Īny help advice is greatly appreciated, i did google this but couldn't find an answer specific to my request so apologies if i am duplicating work here, I'm new to the emulator scene but loving it so far thanks to Recalbox. Is there any known issues with the Pi4 as its new? I'm guessing my games are running slow/laggy due to my Pi1, this is just an experiment as i want to build an arcade cabinet but first i need to know i can get MAME work correctly, i will buy a Pi3 or 4 if this is a success and move to the build project. If i load the game press tab on the keyboard i get the input (general) option and i set UI cancel to the select button and left shoulder, but when i try this nothing happens? If i press select and start together to just goes to a black screen and i have to reboot the Pi. Once in the game how do i return back to the MAME or home screen, exit the game essentially. I installed, setup and copied games over to Recalbox in about an hour and i am playing MAME games, amazing! I spent 2 days trying to get MAME roms working on retropie and kept hitting a brick wall. I'm using a Raspberry Pi1, recalbox 7.1.1 (installed today), installed via etcher.įirst of all, what a great bit of kit Recalbox is, a breathe of fresh air. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |